NOTE 1: Due to shipping restrictions, we donot supply the CR1220 battery in the DS1307 RTC part on the board and the same one in the IR remote.
NOTE 2 : You can go to our google drive to watch the video tutorials and download the documents:
Google Drive: //drive.google.com/drive/folders/0B6uNNXJ2z4CxWjcybmpFOUprRWc?usp=sharing
NOTE 3 : Because The kit Carry the Magnetic Speaker, it can only send by AliExpress Standard Shipping or DHL / UPS / Fedex, if you chose other shipping way , the package may needed to send by AliExpress Standard Shipping or DHL / UPS / Fedex , Please know.
This is a rich sensor module multifunctional kit compatible for Arduino.
The kit include an OPEN-SMART board and 9 sensor module, 3 display module and other accessories.
You can use the kit to do many projects such as Speak Clock / Speak Temperature / Clock display / Infrared Remote Control / Touch Control MP3 / MP3 Player / Ultrasonic Distance Measurement.
OPEN-SMART Board is an ATMEGA328P development board with rich peripherals.
Peripherals on OPEN-SMART Board include 4 digit display, DS1307 clock, LM75 temperature sensor, infrared receiver, serial MP3 player, rotation angle sensor, 4-channel touch sensor. Hardware resources are very rich, do not need any DuPont wires, and the usage is very simple. It is very suitable for learners.
The kit contains TF card, speaker, infrared remote control, and these are the necessary accessories for MP3,DS1307, infrared receiver.
And it contains ultrasonic sensor / water sensor / PIR motion sensor / light sensor / vibration motor / 8 – led bar / I2C 1602 display, etc.
4 digit display: 4 digit tube (0.36 inches) which can display the clock point, it needs D10/D11 pins to control and display the integer, clock, stopwatch, score and so on.
DS1307 clock: based on DS1307 high-precision real-time clock module, I2C interface, the address is 0x68.
LM75 temperature sensor: I2C interface temperature sensor, not only can measure the temperature, it can also set the temperature protection temperature, the address is 0x48.
Infrared receiver: use D2 pin,It can receive the modulated infrared signal of 38KHz that is sent by the IR transmitter module and demodulate it into logic level, and it can complete the infrared remote control with the codec program.
Serial MP3: MP3 music player module is based on high-quality MP3 music chip, use D7 / D8 pins to be software serial port, you can send commands to switch songs, change the volume and play mode and other operations.
Rotation angle sensor: 10K ohm adjustable potentiometer knob angle sensor, use A0 pin, can be used for MP3 volume adjustment, 4-digit display brightness adjustment.
4-CH touch sensor: capacitive touch switch, only when you touch the corresponding position with your fingers, the module corresponding pin (D3 / D4 / D5 / D6) will output high level, otherwise it outputs low.
NTC Temperature Sensor: can measure the temperature directly in the water.
Vibration Motor: a mini vibration motor suitable as a non-audible indicator.
I2C 1602 LCD: a high-quality 2 line 16 character LCD module with I2C interface and it is a basic character LCD screen for lots of applications.
– Use the bootloader for Arduino.
– The program, expansion shields, IDE is compatible for Arduino.
– Use through hole mount type B USB connector, consistent for the Board, ruggedness and long service life.
– You can burn the program with the type A male to type B male cable.
– Onboard 500mA resettable fuse to protect power supply from the USB port and the DC jack at the same time.
– USB interface driver chip: CH340G, compatible with win7, win8, linux, MAC OS.
– Microcontroller: Atmel ATmega328P
– Working voltage: 5V
– IO logic voltage: 5V
– Working current: 500mA (Max)
– Digital I/O Pins: 14 (of which 6 provide PWM output)
– Flash Memory: 32 KB of which 2 KB used by bootloader
– SRAM: 2KB
– EEPROM: 1KB
– Clock Speed: 16 MHz
– Onboard DIP switch, you can disconnect the connection between the peripheral module on the board and the Atmega328P.
– Onboard Shield interface, can plug the compatible expansion shield.
Part List (Schematics and program can be sent, Please contact us)
1 x Board (without CR1220 battery)
1 x IO Shield
1 x USB cable (50cm)
1 x 40pin female to female cable
1 x Voltage sensor
1 x Ultrasonic sensor
1 x Touch sensor
1 x Water sensor
1 x PIR motion sensor
1 x Rocker switch
1 x NTC sensor
1 x Light sensor
1 x Slide Potentiometer
1 x Vibration motor
1 x Passive buzzer
1 x Speaker(1W or 0.5W)
1 x 8 LED bar
1 x Eagle eyes LED
1 x I2C 1602 LCD
1 x 4-Digit display
1 x TF card (256MB)
1 x Infrared Remote Control (without CR1220 battery)
1 x Micro SD card adapter
1 x Infrared emitter
Be the first to review “Rich Sensor Module Starter Kit Atmega328P Development Board w/ IO Shield MP3 DS1307 RTC LCD IR NTC Touch Compatible for Arduino”